T3A in room timer problem - TanToday - Helping Salon Owners, One At A Time, Since 2000!

gottatanfl · 14th June 2006, 10:20 AM

We lost electricity yesterday and when we got it back 3hrs later thanks to the hurricaine, my room 7 3a timer will not connect to the manager. All my other rooms before and after are running fine. We have checked everything unplung the power to manager and chkd all settings on 3a, took the 3a out put in another room and still wouldnt work, It does work as a stand alone, I can operate the 3a from the room to set the bed but not from my manager. ANY ideas Please!!!!!

ADI Tech Support · 14th June 2006, 02:20 PM

Check the address on the T-Max 3A in room 7:

1) If you are using a T-Max Manager or T-Max Manager/Pro, remove power and leave it off.

2) Press and hold the Start/Stop and Up buttons together until a .1 appears on the display. This should take about 5-6 seconds. Release the buttons.

3) Press and release the Start/Stop button. A number and a period will be illuminated with the number flashing. This is the current address of the timer.

Pressing and holding the Up button will cause the display to count up. Holding the Down button will cause the display to count down. Once the count reaches 100, the center period will flash rapidly. This is an indication that you are over 99. For example, if the display shows a 0.2 with the period flashing, this is address 102. The highest the display will count up is 255.

4) Press the Up or Down button until the display reads a .7. Make sure the period is NOT flashing.

5) Press the Start/Stop button. A .1 will be displayed (nothing flashing).

6) To exit Parameter Mode, press and hold the Up and Down buttons together until the period goes away.

7) Re-apply power to your T-Max Manager. See if it picks up room 7.

Kevin Barrett
ADI Tech Support

gottatanfl · 14th June 2006, 02:33 PM

Thank you so much....it was flashing I had it set for 107 not 7 you saved my day

gottatanfl · 26th June 2006, 11:28 AM

The one a couple weeks ago that bounced between a hurricane and a tropical storm for days, it caused enough rain and high winds here to blow out some transformers.

14th June 2006, 10:20 AM	#1 (permalink)
gottatanfl Moderator Join Date: May 2005 Location: unknown Posts: 1,537	T3A in room timer problem We lost electricity yesterday and when we got it back 3hrs later thanks to the hurricaine, my room 7 3a timer will not connect to the manager. All my other rooms before and after are running fine. We have checked everything unplung the power to manager and chkd all settings on 3a, took the 3a out put in another room and still wouldnt work, It does work as a stand alone, I can operate the 3a from the room to set the bed but not from my manager. ANY ideas Please!!!!!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

14th June 2006, 02:20 PM	#2 (permalink)
ADI Tech Support All Star Join Date: Nov 2004 Location: Branson, MO Posts: 146	Check the address on the T-Max 3A in room 7: 1) If you are using a T-Max Manager or T-Max Manager/Pro, remove power and leave it off. 2) Press and hold the Start/Stop and Up buttons together until a .1 appears on the display. This should take about 5-6 seconds. Release the buttons. 3) Press and release the Start/Stop button. A number and a period will be illuminated with the number flashing. This is the current address of the timer. Pressing and holding the Up button will cause the display to count up. Holding the Down button will cause the display to count down. Once the count reaches 100, the center period will flash rapidly. This is an indication that you are over 99. For example, if the display shows a 0.2 with the period flashing, this is address 102. The highest the display will count up is 255. 4) Press the Up or Down button until the display reads a .7. Make sure the period is NOT flashing. 5) Press the Start/Stop button. A .1 will be displayed (nothing flashing). 6) To exit Parameter Mode, press and hold the Up and Down buttons together until the period goes away. 7) Re-apply power to your T-Max Manager. See if it picks up room 7. Kevin Barrett ADI Tech Support

14th June 2006, 02:33 PM	#3 (permalink)
gottatanfl Moderator Join Date: May 2005 Location: unknown Posts: 1,537	Thank you so much....it was flashing I had it set for 107 not 7 you saved my day

26th June 2006, 11:28 AM	#4 (permalink)
gottatanfl Moderator Join Date: May 2005 Location: unknown Posts: 1,537	The one a couple weeks ago that bounced between a hurricane and a tropical storm for days, it caused enough rain and high winds here to blow out some transformers.